RECARO BASE FRAME SEAT RAIL RIGHT SEAT FOR BMW Z3 CH19 CM32 1014.051.2

RECARO

BASE FRAME SEAT RAIL RIGHT SEAT

1014.051.2

BMW Z3 CH19 CM32

Model year: 1997-01-1997-05
Special notes: We recommend replacing the genuine belt buckle with a belt buckle without tensioner function (genuine belt buckle for BMW E30). If you replace the belt buckle, there will be no seat belt tensioner. At the front of the slide position, there is a large interference between the slide lever and the floor under the center console. There is interference between the backrest side and the door armrest.
Notes / Interference information: For LX (including Ergomed series), LS, and LT, replace the recliner dial on the center console side with a thin recliner dial , remove the recliner dial on the door side and replace it with a rubber cap . For the round recliner dial of LX (including Ergomed series) and LS, the recliner dial on the center console side will interfere, so remove the recliner dial on the door side. For the New Ortho (sold until October 2010), the backrest width adjustment dial interferes near the rear end of the sliding position. However, for the New Ortho sold after November 2010, the width adjustment is electric and there is no width adjustment dial on the door side, so there is no interference. For the RMS, please adjust to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RMS side adapter before installation.
Position: One position type
Armrest: Not mountable
Compatible seats: LX / LX-# / LX-VS / LX-VF / LX-VL / Ergomed / Ergomed C / Ergomed D / Ergomed E / Ergomed LD / Ergomed MV (IS-84 base) For LX, LS, LT, and SR, replace the recliner dial (triangle) on the center console side with a thin recliner dial (sold separately) to avoid (reduce) interference with the vehicle, remove the recliner dial (triangle) on the door side to avoid (reduce) interference with the vehicle, and install a rubber cap (sold separately) after removing the recliner dial (triangle). Seats with round recliner dials for LX and LS cannot be replaced with a thin dial (sold separately), so they cannot be installed in vehicles. Classic LX Pepita / Classic LX Spektrum For LX, LS, LT, and SR, replace the recliner dial (triangle) on the center console side with a thin recliner dial (sold separately) to avoid (reduce) interference with the vehicle, remove the recliner dial (triangle) on the door side to avoid (reduce) interference with the vehicle, and attach a rubber cap (sold separately) after removing the recliner dial (triangle). The seat of the round recliner dial of LX and LS cannot be replaced with the thin dial sold separately, so it cannot be installed in the vehicle. LS / LS-# / LT-# For LX, LS, LT, and SR, replace the recliner dial (triangle) on the center console side with a thin recliner dial (sold separately) to avoid (reduce) interference with the vehicle, remove the recliner dial (triangle) on the door side to avoid (reduce) interference with the vehicle, and attach a rubber cap (sold separately). The seat of the round recliner dial of LX and LS cannot be replaced with the thin dial sold separately, so it cannot be installed in the vehicle. Pro Racer RMS RMS should be adjusted to the optimal position (front/rear height, left/right offset 0/5/10mm) using the separately sold RMS side adapter (part number 1700002J). If there is any interference with the interior, it can be mitigated by adjustment. New Orthoped (with Recaro vent)
SP-AN / SP-GN / SP-GN 2 SP-AN / SP-GN / SP-GN 2 requires the separately sold SP-GN side adapter set (part number 1600110J). AM19 STYLE-J/JJ/JC
AM19 TREND-JS
AM19 STYLE-JS
AM19 SPORT-JS
AM19 STYLE-D/DC
TS-G / RS-G / TS-W / RS-W You will need to purchase the side adapter set (part number 1700000J) separately.

(Note) This product cannot be installed on any seats other than those listed in the matching information below. Only for the Roadster Anniversary model.

Images are for illustration purpose only. Actual product may vary.