RECARO BASE FRAME SEAT RAIL LEFT SEAT FOR PORSCHE 911 991 2013.031.1

RECARO

BASE FRAME SEAT RAIL LEFT SEAT

2013.031.1

PORSCHE 911 991

Model year: 2011-11-2019-12
Special notes: The side airbag function built into the original seat will be lost. Airbag warning light must be turned off. The seating position when installing the RS-G will vary depending on the side adapter used. When using the offset side adapter for RS/TS-G, the seat will be about 20 mm higher than the lowest position of the original seat when using the top of the mounting hole and one 6 mm spacer. (Similarly, it will be about 7 mm higher when using the bottom of the mounting hole and one 6 mm spacer.) In this case, there is no seat offset. On the other hand, when using a normal side adapter, the seat will be about 15 mm higher than the lowest position of the original seat when using the top of the mounting hole and two 6 mm spacers. (Similarly, it will be about 8 mm lower when using the bottom of the mounting hole and one 6 mm spacer.) In this case, the seat offset is about 10 mm toward the door (Recaro moves closer to the door). The amount of sliding backwards is reduced by about 20 mm compared to the original (when installing RS-G). Other Recaro seats cannot be installed because the rear position of the seat slide interferes with the interior of the car and reduces the slide amount (approximately 40mm to 60mm). *Although it is not recommended, we will state for reference that there are cases of dealers installing the SPORT-JC, Sportster, and Cross Sportster, which we receive many inquiries about. However, for the Sportster and Cross Sportster, the reclining dial interferes with the floor at the rear of the slide position (to a level that does not cause any obstruction except for those who drive in the rear position). For details, please contact a dealer that is familiar with the vehicle.
Notes / Interference information: If you prioritize seat height over steering wheel offset, please use the separate side adapter for RS-G installation. Also, if you are more concerned about steering wheel offset than seat height, you can also choose the offset adapter set for RS/TS-G for RS/TS-# series. This allows you to adjust the steering wheel offset in 5mm increments from 5mm to a maximum of 15mm. (When installing, please consult with your dealer regarding interference with the console side (shift, etc.)). SP-# requires the SP-G offset adapter set (product number 1600094J). When SP-# is installed, the offset is approximately 8mm toward the console side (Recaro moves closer to the console side). For RMS, adjust to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RMS side adapter before installing. Also, if there is interference with the interior, it can be alleviated by adjustment.
Position: New structure frame. One-position type.
Armrest: Cannot be installed
Compatible seats: Pro Racer RMS For RMS, adjust to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RMS side adapter (product number 1700002J). Also, if there is interference with the interior, it can be alleviated by adjustment. SP-A / SP-G / SP-G2 / SP-G3 / SP-GT / SP-GT2 SP-# and Racer require the separately sold SP-G offset adapter set (product number 1600094J). TS-G / RS-G / TS-W / RS-W For RS/TS-# series, please choose from two types of separately sold side adapter set or RS/TS-G offset adapter set. [Seating position priority] Side adapter set (product number 1700000J) [Offset priority] RS/TS-G offset adapter set (product number 1700001J) Handle offset can be adjusted by 5/10/15mm left and right offset. (Seating position is raised by +5mm.)

(Note) This product cannot be installed on any seats other than those listed in the matching information below. Side airbag canceller included. Not confirmed for GT3.

Images are for illustration purpose only. Actual product may vary.