$268.06 SGD
| /
| Brand | RECARO |
| Series Name | BASE FRAME SEAT RAIL LEFT SEAT |
| Product Number | 2080.029.1 |
| Compatible Car | TOYOTA VITZ NSP130 *NCP131 RS ETC. AND NHP130 HYBRID RELEASED IN JANUARY 2017 PLEASE USE THE BASE FRAME NCP131. P135 4WD IS NOT AVAILABLE. |
| Product Description | Model year: 2010-12-2020-02 Special notes: The side airbag function built into the factory seat will be lost. For vehicles equipped with side airbags, the airbag warning light must be turned off. When the adapter frame is installed, the seating position will be approximately 25 mm higher than the lowest position of the factory seat. When the adapter frame is not installed, the seating position will be approximately 15 mm lower than the lowest position of the factory seat (when using ST-JJ). The forward sliding amount is reduced by approximately 20 mm compared to the factory. If a Recaro seat is installed in the passenger seat, the occupant detection sensor will no longer function and the seat belt warning light will no longer be turned on. Notes / Interference information: For LX (including Ergomed series), the recliner dial on the center console side must be replaced with a thin recliner dial (product number 1600090J). For SP-#, an SP-G offset adapter set (product number 1600094J) is required. For Trend-J, JJ, JC, D, and DC, the backrest side and door armrest interfere with each other by approximately 10 to 15 mm. For Sport-J, JJ, JC, D, and DC, the backrest side and door armrest interfere with each other by approximately 5 to 10 mm. For RMS, please adjust to the optimal position (front-to-back height, left-to-right offset 0/5/10 mm) using the separately sold RMS side adapter before installation. If there is interference with the interior, this can be alleviated by adjustment. For RCS, please adjust to the optimal position (front-to-back height, left-to-right offset 0/5/10 mm) using the separately sold RCS side adapter before installation. Position: New structure frame. One-position type. Armrest: Can be installed on the right hand side of the left seat, or on the left hand side of the right seat Compatible seats: LX / LX-# / LX-VS / LX-VF / LX-VL / Ergomed / Ergomed C / Ergomed D / Ergomed E / Ergomed LD / Ergomed MV (IS-84 base) Replace with a thin recliner dial (sold separately) to avoid (soften) interference with the vehicle Classic LX Pepita / Classic LX Spektrum Replace with a thin recliner dial (sold separately) to avoid (soften) interference with the vehicle LX-F (IS-05 base) Pro Racer RMS RMS should be installed after adjusting to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the RMS side adapter (product number 1700002J) sold separately. In addition, if there is interference with the interior, it can be softened by adjustment. New Orthoped (with Recaro vent) RCS Please adjust the RCS to the optimal position (front/rear height, left/right offset 0/5/10mm) using the separately sold RCS side adapter before installation. *Please choose from the following two types. ・RCS side adapter AM19 STYLE-J/JJ/JC AM19 SPORT-J/JJ/JC AM19 TREND-JS AM19 STYLE-JS AM19 SPORT-JS AM19 TREND-D/DC AM19 STYLE-D/DC AM19 SPORT-D/DC/MAGNIFICA CL222HV TS-G / RS-G / TS-W / RS-W Side adapter set (product number 1700000J) must be purchased separately. SR-6 /SR-11/SR-7 SR-S SR-C/ SR-7F |
| Remarks | (Note) This product cannot be installed on any seats other than those listed in the matching information below. Sports frame (with adapter frame). 2WD vehicles. Side airbag canceller included. *For NCP131 (RS, etc.) and NHP130 (hybrid released in January 2017), please use the base frame for NCP131. Not compatible with P135 4WD. Product number changed from April 3, 2019. Position remains unchanged. |
| Notes | Images are for illustration purpose only. Actual product may vary. |
