RECARO BASE FRAME SEAT RAIL RIGHT SEAT FOR TOYOTA SUCCEED PROBOX NCP55 58 51 59 2080.376.2

RECARO

BASE FRAME SEAT RAIL RIGHT SEAT

2080.376.2

TOYOTA SUCCEED PROBOX NCP55 58 51 59

Model year: 2002-07-2014-08
Special notes: The seating position is approximately 20mm lower than the lowest position of the genuine seat (when using ST-JJ center hole). Handle offset door side 10mm (Recaro moves closer to the door side).
Notes / Interference information: CS, CSE, CT, C-clutch use a spacer, so the seating position will be higher by the amount of the spacer. For RS/TS-# series, the handle offset can be adjusted in 5mm increments from 5mm to a maximum of 15mm by using the RS/TS-G offset adapter set (product number 1700001J). (When installing, please consult your dealer regarding interference with the console side (shift, etc.). For RMS, please adjust to the optimal position (front/rear height, left/right offset 0/5/10mm) using the RMS side adapter sold separately. In addition, if there is interference with the interior, it can be alleviated by adjustment. Please adjust the RCS to the optimal position (front/rear height, left/right offset 0/5/10mm) using the separately sold RCS side adapter.
Position: New structure frame. Choose from 3 different heights (For some car models, the legs of the slide rail may need to be cut depending on the installation position. Please test fit before installation.)
Armrest: Can be installed for the right hand of the left seat, or the left hand of the right seat
Compatible seats: LX / LX-# / LX-VS / LX-VF / LX-VL / Ergomed / Ergomed C / Ergomed D / Ergomed E / Ergomed LD / Ergomed MV (IS-84 base)
Classic LX Pepita / Classic LX Spektrum
LX-F (IS-05 base)
LS / LS-# / LT-#
CS / CR / CG / Conformed
CSE
CT
C-Classic
Pro Racer RMS RMS can be installed with the separately sold RMS side adapter (product number 1700002J). Please adjust to the optimal position (front/rear height, left/right offset 0/5/10mm) before installation. Also, if there is interference with the interior, it can be mitigated by adjustment. New Orthoped (with Recaro vent)
RCS Please adjust the RCS to the optimal position (front/rear height, left/right offset 0/5/10mm) before installation using the separately sold RCS side adapter. *Please choose from the following two types.・Side adapter for RCS ・Stainless steel side adapter set for RCS SR-2 late model / SR-3 / SR-4 / SR-5 / SR-VF / SR-IMPACT / SR-IMPACT Pro
Rally Special / First generation SR / Early SR-2
Late model A-8
Early model A-8
SP-A / SP-G / SP-G2 / SP-G3 / SP-GT / SP-GT2 You will need to purchase the side adapter set separately. SP-AN / SP-GN / SP-GN 2 SP-AN / SP-GN / SP-GN 2 require the separately sold SP-GN side adapter set . You will need to purchase the PRO RACER(RACER) SP-G/A Side Adapter Set (product number 1700000J) separately. AM19 TREND-J/JJ/JC
AM19 STYLE-J/JJ/JC
AM19 SPORT-J/JJ/JC
AM19 TREND-JS
AM19 STYLE-JS
AM19 SPORT-JS
AM19 TREND-D/DC
AM19 STYLE-D/DC
AM19 SPORT-D/DC/MAGNIFICA CL222HV
TS-G / RS-G / TS-W / RS-W For RS/TS-# series, please choose from two types of offset adapter sets for RS/TS-G or the side adapter set sold separately. [Priority on seating position] Side adapter set [Priority on offset] Offset adapter set for RS/TS-G Handle offset can be adjusted to 5/10/15mm left and right. (Seating position is raised by +5mm.) SP-X
SR-6 /SR-11/SR-7
SR-S
SR-C/ SR-7F
Sportster
CrossSportster

(Note) This product cannot be installed on any seats other than those listed in the matching information below. Wagon, van

Images are for illustration purpose only. Actual product may vary.