RECARO BASE FRAME SEAT RAIL LEFT SEAT FOR TOYOTA WISH ZGE20 21 2080.539.1

RECARO

BASE FRAME SEAT RAIL LEFT SEAT

2080.539.1

TOYOTA WISH ZGE20 21

Model year: 2009-03-2017-10
Special notes: The side airbag function built into the factory seat will be lost. Airbag warning light must be turned off. The seating position will be a few mm lower than the lowest position of the factory seat (when using ST-JJ center hole). Steering wheel offset console side 10 mm (Recaro moves closer to the center console).
Notes / Interference information: For RS/TS-# series, the steering wheel offset can be adjusted in 5 mm increments from 5 mm to a maximum of 15 mm using the RS/TS-G offset adapter set (product number 1700001J). (Please consult your dealer regarding interference with the console side (shift, etc.) when installing.) For RMS, adjust to the optimal position (front/rear height, left/right offset 0/5/10 mm) using the separately sold RMS side adapter before installation. In addition, if there is interference with the interior, it can be alleviated by adjustment. Please adjust the RCS to the optimal position (front/rear height, left/right offset 0/5/10mm) using the separately sold RCS side adapter.
Position: New structure frame. Choose from 3 different heights (For some car models, the legs of the slide rail may need to be cut depending on the installation position. Please test fit before installation.)
Armrest: Can be installed for the right hand of the left seat, and for the left hand of the right seat
Compatible seats: LX / LX-# / LX-VS / LX-VF / LX-VL / Ergomed / Ergomed C / Ergomed D / Ergomed E / Ergomed LD / Ergomed MV (IS-84 base)
Classic LX Pepita / Classic LX Spektrum
LX-F (IS-05 base)
LS / LS-# / LT-#
CS / CR / CG / Conformed
CSE
CT
C-Classic
D / DH / DV
DS / DS-H / DS-V / ES-V/DSE
Pro Racer RMS RMS should be installed after adjusting to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RMS side adapter . In addition, any interference with the interior can be alleviated by adjustment. New Orthoped (with Recaro vent)
RCS RCS should be installed after adjusting to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RCS side adapter. *Please choose from the following two types.・Side adapter for RCS ・Stainless steel side adapter set for RCS SR-2 late model / SR-3 / SR-4 / SR-5 / SR-VF / SR-IMPACT / SR-IMPACT Pro
Rally Special / First generation SR / Early SR-2
Late model A-8
Early model A-8
SP-A / SP-G / SP-G2 / SP-G3 / SP-GT / SP-GT2 You will need to purchase the side adapter set separately. SP-AN / SP-GN / SP-GN 2 SP-AN / SP-GN / SP-GN 2 require the separately sold SP-GN side adapter set . You will need to purchase the PRO RACER(RACER) SP-G/A Side Adapter Set (product number 1700000J) separately. AM19 TREND-J/JJ/JC
AM19 STYLE-J/JJ/JC
AM19 SPORT-J/JJ/JC
AM19 TREND-JS
AM19 STYLE-JS
AM19 SPORT-JS
AM19 TREND-D/DC
AM19 STYLE-D/DC
AM19 SPORT-D/DC/MAGNIFICA CL222HV
TS-G / RS-G / TS-W / RS-W For RS/TS-# series, please choose from two types of offset adapter sets for RS/TS-G or the side adapter set sold separately. [Priority on seating position] Side adapter set [Priority on offset] Offset adapter set for RS/TS-G Handle offset can be adjusted to 5/10/15mm left and right. (Seating position is raised by +5mm.) SP-X
SR-6 /SR-11/SR-7
SR-S
SR-C/ SR-7F
Sportster
CrossSportster

(Note) This product cannot be installed on any seats other than those listed in the matching information below. Side airbag canceller included. 2WD vehicle.

Images are for illustration purpose only. Actual product may vary.