RECARO BASE FRAME SEAT RAIL RIGHT SEAT FOR MAZDA RX-7 FD3S ONE POSITION FRAME 2082.286.2

RECARO

BASE FRAME SEAT RAIL RIGHT SEAT

2082.286.2

MAZDA RX-7 FD3S ONE POSITION FRAME

Model year: 1991-10-2002-08
Special notes: The headrest interferes with the ceiling near the rear end of the sliding position. The seating position is about 10mm higher than the OEM seat. The door trim and recliner dial interfere with each other, making it harder to slide, and the amount of sliding backwards is also reduced.
Notes / Interference information: For LX (including Ergomed series), LS, and LT, replace the recliner dial on the center console with a thin recliner dial , remove the recliner dial on the door side and replace it with a rubber cap .
Position: New structure frame. One-position type.
Armrest: Cannot be installed
Compatible seats: LX / LX-# / LX-VS / LX-VF / LX-VL / Ergomed / Ergomed C / Ergomed D / Ergomed E / Ergomed LD / Ergomed MV (IS-84 base) For LX, LS, LT, and SR, replace the recliner dial (triangle) on the center console side with a thin recliner dial (sold separately) to avoid (reduce) interference with the vehicle, remove the recliner dial (triangle) on the door side to avoid (reduce) interference with the vehicle, and install a rubber cap (sold separately) after removing the recliner dial (triangle). Seats with round recliner dials for LX and LS cannot be replaced with a thin dial (sold separately), so they cannot be installed in vehicles. Classic LX Pepita / Classic LX Spektrum For LX, LS, LT, and SR, replace the recliner dial (triangle) on the center console side with a thin recliner dial (sold separately) to avoid (reduce) interference with the vehicle, remove the recliner dial (triangle) on the door side to avoid (reduce) interference with the vehicle, and attach a rubber cap (sold separately) after removing the recliner dial (triangle). The seat of the round recliner dial of LX and LS cannot be replaced with the thin dial sold separately, so it cannot be installed in the vehicle. LS / LS-# / LT-# For LX, LS, LT, and SR, replace the recliner dial (triangle) on the center console side with a thin recliner dial (sold separately) to avoid (reduce) interference with the vehicle, remove the recliner dial (triangle) on the door side to avoid (reduce) interference with the vehicle, and attach a rubber cap (sold separately). The seat of the round recliner dial of LX and LS cannot be replaced with the thin dial sold separately, so it cannot be installed in the vehicle. Pro Racer RMS RMS should be adjusted to the optimal position (front/rear height, left/right offset 0/5/10mm) using the RMS side adapter sold separately (product number 1700002J). If there is any interference with the interior, it can be mitigated by adjustment. New Orthoped (with Recaro vent)
SR-2 late model / SR-3 / SR-4 / SR-5 / SR-VF / SR-IMPACT / SR-IMPACT Pro For LX, LS, LT, and SR, replace the recliner dial (triangle) on the center console side with a thin recliner dial (sold separately) to avoid (mitigate) interference with the vehicle, remove the recliner dial (triangle) on the door side to avoid (mitigate) interference with the vehicle, and remove the recliner dial (triangle) and then install the rubber cap (sold separately). The round recliner dial seats for LX and LS cannot be replaced with the thin dial sold separately, so they cannot be installed in the vehicle. SP-A / SP-G / SP-G2 / SP-G3 / SP-GT / SP-GT2 SP-# and Racer require the separately sold SP-G Offset Adapter Set (Part No. 1600094J). SP-AN / SP-GN / SP-GN 2 SP-AN / SP-GN / SP-GN 2 require the separately sold SP-GN Side Adapter Set (Part No. 1600110J).

(Note) This product cannot be installed on any seats other than those listed in the matching information below.

Images are for illustration purpose only. Actual product may vary.