RECARO BASE FRAME SEAT RAIL LEFT SEAT FOR HONDA MOBILIO SPIKE GK1 2 2085.016.1

RECARO

BASE FRAME SEAT RAIL LEFT SEAT

2085.016.1

HONDA MOBILIO SPIKE GK1 2

Model year: 2002-09-2004-01
Special notes: The seating position will be 10mm lower than the lowest position of the original seat (when using ST-JJ center hole). If only the right seat is replaced with a Recaro, the seat cushion side will interfere with the original seat surface, and the belt buckle will interfere with the original seat surface, so the seat position must be set to the highest position before installation.
Notes / Interference information: SR-1, 2 have about 10-15mm interference between the shoulder and B-pillar. SP-# and Racer require the SP-G offset adapter set (product number 1600094J). For RMS, please adjust to the optimal position (front-rear height, left-right offset 0/5/10mm) using the separately sold RMS side adapter. Also, if there is interference with the interior, it can be alleviated by adjustment. For RCS, please adjust to the optimal position (front-rear height, left-right offset 0/5/10mm) using the separately sold RCS side adapter.
Position: New structural frame. Choose from 3 different heights (For some car models, the legs of the slide rail may need to be cut depending on the installation position. Please test fit before installation.)
Armrest: Can be installed for the right hand of the left seat, or the left hand of the right seat
Compatible seats: LX / LX-# / LX-VS / LX-VF / LX-VL / Ergomed / Ergomed C / Ergomed D / Ergomed E / Ergomed LD / Ergomed MV (IS-84 base)
Classic LX Pepita / Classic LX Spektrum
LX-F (IS-05 base)
LS / LS-# / LT-#
CS / CR / CG / Conformed
CSE
CT
C-Classic
D / DH / DV
DS / DS-H / DS-V / ES-V/DSE
Pro Racer RMS RMS should be installed after adjusting to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RMS side adapter . In addition, any interference with the interior can be alleviated by adjustment. New Orthoped (with Recaro vent)
RCS RCS should be installed after adjusting to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RCS side adapter. *Please choose from the following two types.・Side adapter for RCS ・Stainless steel side adapter set for RCS SR-2 late model / SR-3 / SR-4 / SR-5 / SR-VF / SR-IMPACT / SR-IMPACT Pro
Rally Special / First generation SR / Early SR-2
Late model A-8
Early model A-8
SP-A / SP-G / SP-G2 / SP-G3 / SP-GT / SP-GT2 SP-# and Racer require the separately sold SP-G offset adapter set . SP-AN / SP-GN / SP-GN 2 SP-AN / SP-GN / SP-GN 2 require the separately sold SP-GN side adapter set . For PRO RACER(RACER) SP-G/A SP-# and Racer, you will need the separately sold SP-G Offset Adapter Set (Part number 1600094J). AM19 TREND-J/JJ/JC
AM19 STYLE-J/JJ/JC
AM19 SPORT-J/JJ/JC
AM19 TREND-JS
AM19 STYLE-JS
AM19 SPORT-JS
AM19 TREND-D/DC
AM19 STYLE-D/DC
AM19 SPORT-D/DC/MAGNIFICA CL222HV
TS-G / RS-G / TS-W / RS-W You will need to purchase the separately sold Side Adapter Set (Part number 1700000J). SP-X
SR-6 /SR-11/SR-7
SR-S
SR-C/ SR-7F
Sportster
CrossSportster

(Note) This product cannot be installed on any seats other than those listed in the matching information below. Vehicles without i-side airbags. Not confirmed after minor changes.

Images are for illustration purpose only. Actual product may vary.