RECARO BASE FRAME SEAT RAIL LEFT SEAT FOR DAIHATSU YRV M200 2087.103.1

RECARO

BASE FRAME SEAT RAIL LEFT SEAT

2087.103.1

DAIHATSU YRV M200

Model year: 2000-08-2005-07
Special notes: The seating position is almost the same as the genuine seat (when using ST-JJ center hole).
Cautions / Interference information: For LX (including Ergomed), LS, LT, SR-1, 2, 3, 4, 5, and new A-8, remove the door-side recliner dial and replace it with a rubber cap (product number 1600091J). For LX (including Ergomed), and LS round recliner dials, remove the door-side recliner dial. For Trend-J, JJ, JC, D, and DC, the backrest side and door armrest interfere by a few mm. For RMS, adjust to the optimal position (front-to-back height, left-to-right offset 0/5/10 mm) using the RMS side adapter (sold separately). If there is interference with the interior, it can be alleviated by adjustment. Please adjust the RCS to the optimal position (front/rear height, left/right offset 0/5/10mm) using the separately sold RCS side adapter before installing.
Position: New structure frame. 3 height settings available (For some car models, the legs of the slide rail need to be cut depending on the installation position, so please do a trial fit before installation.)
Armrest: Can be installed for the right hand on the left seat, or the left hand on the right seat
Compatible seats: LX / LX-# / LX-VS / LX-VF / LX-VL / Ergomed / Ergomed C / Ergomed D / Ergomed E / Ergomed LD / Ergomed MV (IS-84 base) Remove the recliner dial to avoid (soften) interference with the vehicle, and install the rubber cap (sold separately) after removing the recliner dial. Classic LX Pepita / Classic LX Spektrum Remove the recliner dial to avoid (soften) interference with the vehicle, and then remove the recliner dial and attach the rubber cap (sold separately). LX-F (IS-05 base)
LS / LS-# / LT-# Remove the recliner dial to avoid (soften) interference with the vehicle, and then remove the recliner dial and attach the rubber cap (sold separately). Pro Racer RMS RMS should be installed after adjusting to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RMS side adapter . Also, if there is interference with the interior, it can be softened by adjustment. New Orthoped (with Recaro vent)
RCS RCS should be installed after adjusting to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RCS side adapter. *Please choose from the following two types.・Side adapter for RCS ・Stainless steel side adapter set for RCS SR-2 late model / SR-3 / SR-4 / SR-5 / SR-VF / SR-IMPACT / SR-IMPACT Pro Remove the recliner dial to avoid (reduce) interference with the vehicle, and attach the rubber cap (sold separately) after removing the recliner dial. Rally Special / First generation SR / Early SR-2 Remove the recliner dial to avoid (reduce) interference with the vehicle, and attach the rubber cap (sold separately) after removing the recliner dial. Late model A-8 Remove the recliner dial to avoid (reduce) interference with the vehicle, and attach the rubber cap (sold separately). SP-A / SP-G / SP-G2 / SP-G3 / SP-GT / SP-GT2 You will need to purchase the side adapter set separately. SP-AN / SP-GN / SP-GN 2 SP-AN / SP-GN / SP-GN 2 require the separately sold SP-GN side adapter set (product number 1600110J). PRO RACER (RACER) SP-G/A side adapter set (product number 1700000J) must be purchased separately. AM19 TREND-J/JJ/JC
AM19 STYLE-J/JJ/JC
AM19 SPORT-J/JJ/JC
AM19 TREND-JS
AM19 STYLE-JS
AM19 SPORT-JS
AM19 TREND-D/DC
AM19 STYLE-D/DC
AM19 SPORT-D/DC/MAGNIFICA CL222HV
TS-G / RS-G / TS-W / RS-W Side adapter set (product number 1700000J) must be purchased separately. SR-6 /SR-11/SR-7
SR-S
SR-C/ SR-7F

(Note) This product cannot be installed on any seats other than those listed in the matching information below.

Images are for illustration purpose only. Actual product may vary.