RECARO BASE FRAME SEAT RAIL RIGHT SEAT FOR TOYOTA PRIUS Α 7-SEATER ZVW40W 7-SEATER 2080.002.2

RECARO

BASE FRAME SEAT RAIL RIGHT SEAT

2080.002.2

TOYOTA PRIUS Α 7-SEATER ZVW40W 7-SEATER

Model year: 2011-05-2021-03
Special notes: The side airbag function built into the factory seat will be lost. Vehicles equipped with side airbags will require the airbag warning light to be turned off. The seating position is approximately 30 mm higher when using the upper position of the three-stage adjustment compared to the lowest position of the factory seat height adjustment function, approximately 17 mm higher when using the center position, and approximately 4 mm higher when using the lower position. Also, compared to the highest position of the factory seat height adjustment function, the upper position of the three-stage adjustment is approximately 34 mm lower and the lower position is approximately 60 mm lower. (When using ST-JJ). The seat lateral position is 5 mm closer to the door than the factory seat. The steering wheel offset is 5 mm closer to the door. The slide position is 20 mm shorter forward than the factory seat. When a Recaro seat is installed in the passenger seat, the occupant detection sensor will no longer function and the seat belt warning light will no longer be turned on.
Notes / Interference information: Please adjust the RMS to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RMS side adapter before installation. Also, if there is interference with the interior, it can be alleviated by adjustment. Please adjust the RCS to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RCS side adapter before installation.
Position: New structure frame. 3 height settings available (For some models, the legs of the slide rail need to be cut depending on the installation position. Please perform a trial fit before installation.)
Armrest: Not compatible
Compatible seats: LX / LX-# / LX-VS / LX-VF / LX-VL / Ergomed / Ergomed C / Ergomed D / Ergomed E / Ergomed LD / Ergomed MV (IS-84 base)
Classic LX Pepita / Classic LX Spektrum
LX-F (IS-05 base)
LS / LS-# / LT-#
Pro Racer RMS RMS is installed after adjusting to the optimal position (front-rear height, left-right offset 0/5/10mm) with the separately sold RMS side adapter . In addition, if there is interference with the interior, it can be mitigated by adjustment. New Orthoped (with Recaro vent)
RCS Please adjust the RCS to the optimal position (front/rear height, left/right offset 0/5/10mm) using the separately sold RCS side adapter before installation. *Please choose from the following two types. ・RCS side adapter ・RCS stainless steel side adapter set SP-A / SP-G / SP-G2 / SP-G3 / SP-GT / SP-GT2 You will need to purchase the side adapter set separately. SP-AN / SP-GN / SP-GN 2 SP-AN / SP-GN / SP-GN 2 will require the separately sold SP-GN side adapter set . PRO RACER (RACER) SP-G/A You will need to purchase the side adapter set separately. AM19 TREND-J/JJ/JC
AM19 STYLE-J/JJ/JC
AM19 SPORT-J/JJ/JC
AM19 TREND-JS
AM19 STYLE-JS
AM19 SPORT-JS
AM19 TREND-D/DC
AM19 STYLE-D/DC
AM19 SPORT-D/DC/MAGNIFICA CL222HV
TS-G / RS-G / TS-W / RS-W Side adapter set (product number 1700000J) must be purchased separately. SP-X
SR-6 /SR-11/SR-7
SR-S
SR-C/ SR-7F
Sportster
CrossSportster

(Note) This product cannot be installed on any seats other than those listed in the matching information below. Side airbag canceller included. Compatibility with vehicles with optional seat accessories has not been confirmed. *For 7-seater vehicles only

Images are for illustration purpose only. Actual product may vary.