RECARO BASE FRAME SEAT RAIL RIGHT SEAT FOR TOYOTA ISIS NM10 DRIVER'S SEAT 2080.390.2

RECARO

BASE FRAME SEAT RAIL RIGHT SEAT

2080.390.2

TOYOTA ISIS NM10 DRIVER'S SEAT

Model year: 2004-09-2009-09
Special notes: The seating position is almost the same as the OEM seat (when using ST-JJ center hole). The forward sliding amount is reduced by about 20mm compared to the OEM.
Notes / Interference information: For SR-3, 4, 5, the backrest side and door armrest interfere by about 5-10mm. For SR-1, 2, the backrest side and door armrest interfere by about 5-10mm, and the shoulder part and B-pillar interfere by about 10-15mm. For SP-# and Racer, the SP-G offset adapter set (product number 1600094J) is required. For SP-#N, the shoulder part interferes with the B-pillar by a few mm. For Trend-J, JJ, JC, D, DC, the backrest side and door armrest interfere by about 10-15mm. For Sport-J, JJ, JC, D, DC, the backrest side and door armrest interfere by about 5-10mm. The CS and CSE use spacers, so the seating position will be higher by the amount of the spacer. For the RMS, please adjust to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RMS side adapter before installation. In addition, any interference with the interior can be alleviated by adjustment. For the RCS, please adjust to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RCS side adapter before installation. Position: New structure frame. English: Choose from 3 height levels (For some car models, the legs of the slide rail may need to be cut depending on the installation position, so please test fit before installation.)
Armrest: Cannot be installed
Compatible seats: LX / LX-# / LX-VS / LX-VF / LX-VL / Ergomed / Ergomed C / Ergomed D / Ergomed E / Ergomed LD / Ergomed MV (IS-84 base)
Classic LX Pepita / Classic LX Spektrum
LX-F (IS-05 base)
LS / LS-# / LT-#
CS / CR / CG / Conformed
CSE
Pro Racer RMS For the RMS, please adjust to the optimal position (front/rear height, left/right offset 0/5/10mm) using the separately sold RMS side adapter . Also, if there is any interference with the interior, it can be mitigated by adjustment. New Orthoped (with Recaro vent)
RCS Please adjust the RCS to the optimal position (front/rear height, left/right offset 0/5/10mm) using the separately sold RCS side adapter before installing. *Please choose from the following two types.・Side adapter for RCS ・Stainless steel side adapter set for RCS SR-2 late model / SR-3 / SR-4 / SR-5 / SR-VF / SR-IMPACT / SR-IMPACT Pro
Rally Special / First generation SR / Early SR-2
Late model A-8
Early model A-8
SP-A / SP-G / SP-G2 / SP-G3 / SP-GT / SP-GT2 SP-# and Racer require the separately sold SP-G offset adapter set . SP-AN / SP-GN / SP-GN 2 SP-AN / SP-GN / SP-GN 2 require the separately sold SP-GN side adapter set . For PRO RACER(RACER) SP-G/A SP-# and Racer, you will need the separately sold SP-G Offset Adapter Set (Part number 1600094J). AM19 TREND-J/JJ/JC
AM19 STYLE-J/JJ/JC
AM19 SPORT-J/JJ/JC
AM19 TREND-JS
AM19 STYLE-JS
AM19 SPORT-JS
AM19 TREND-D/DC
AM19 STYLE-D/DC
AM19 SPORT-D/DC/MAGNIFICA CL222HV
TS-G / RS-G / TS-W / RS-W You will need to purchase the separately sold Side Adapter Set (Part number 1700000J). SP-X
SR-6 /SR-11/SR-7
SR-S
SR-C/ SR-7F
Sportster
CrossSportster

(Note) This product cannot be installed on any seats other than those listed in the matching information below. Driver's seat frame. No side airbags, 2WD vehicles.

Images are for illustration purpose only. Actual product may vary.