RECARO BASE FRAME SEAT RAIL RIGHT SEAT FOR TOYOTA MARK II CHASER X110 2080.581.2

RECARO

BASE FRAME SEAT RAIL RIGHT SEAT

2080.581.2

TOYOTA MARK II CHASER X110

Model year: 2000-10-2004-10
Special notes: The seating position is approximately 10mm lower than the lowest position of the original seat (when using ST-JJ center hole). When installing the seat at the lowest position, the legs of the slide rail will interfere with the floor, so you will need to cut the legs of the slide rail.
Notes / Interference information: For CS, CSE, CT, C-class, D, DS, and DSE, remove the recliner cover on the center console side. For RMS, adjust to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RMS side adapter before installation. Also, if there is interference with the interior, it can be alleviated by adjustment. For RCS, adjust to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RCS side adapter before installation.
Position: New structure frame. Choose from 3 height settings (For some car models, the legs of the slide rail may need to be cut depending on the installation position. Please test fit before installation.)
Armrest: Cannot be installed
Compatible seats: LX / LX-# / LX-VS / LX-VF / LX-VL / Ergomed / Ergomed C / Ergomed D / Ergomed E / Ergomed LD / Ergomed MV (IS-84 base)
Classic LX Pepita / Classic LX Spektrum
LX-F (IS-05 base)
LS / LS-# / LT-#
CS / CR / CG / Conformed Remove the side cover (recliner cover) to avoid (reduce) interference with the vehicle CSE Remove the side cover (recliner cover) to avoid (reduce) interference with the vehicle CT Remove the side cover (recliner cover) to avoid (reduce) interference with the vehicle C-Classic Remove the side cover (recliner cover) to avoid (reduce) interference with the vehicle D / DH / DV Remove the side cover (recliner cover) to avoid (reduce) interference with the vehicle DS / DS-H / DS-V / ES-V/DSE Remove the side cover (recliner cover) to avoid (reduce) interference with the vehicle Pro Racer RMS RMS should be installed after adjusting to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RMS side adapter . Also, if there is interference with the interior, it can be reduced by adjustment. New Orthoped (with Recaro vent)
RCS RCS should be installed after adjusting to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RCS side adapter. *Please choose from the following two types.・Side adapter for RCS ・Stainless steel side adapter set for RCS SR-2 late model / SR-3 / SR-4 / SR-5 / SR-VF / SR-IMPACT / SR-IMPACT Pro
Rally Special / First generation SR / Early SR-2
Late model A-8
Early model A-8
SP-A / SP-G / SP-G2 / SP-G3 / SP-GT / SP-GT2 You will need to purchase the side adapter set separately. SP-AN / SP-GN / SP-GN 2 SP-AN / SP-GN / SP-GN 2 require the separately sold SP-GN side adapter set . You will need to purchase the PRO RACER(RACER) SP-G/A side adapter set (product number 1700000J) separately. AM19 TREND-J/JJ/JC
AM19 STYLE-J/JJ/JC
AM19 SPORT-J/JJ/JC
AM19 TREND-JS
AM19 STYLE-JS
AM19 SPORT-JS
AM19 TREND-D/DC
AM19 STYLE-D/DC
AM19 SPORT-D/DC/MAGNIFICA CL222HV
You will need to purchase the TS-G / RS-G / TS-W / RS-W side adapter set (product number 1700000J) separately. SP-X
SR-6 /SR-11/SR-7
SR-S
SR-C/ SR-7F
Sportster
CrossSportster

(Note) This product cannot be installed on any seats other than those listed in the matching information below. Including the Bullitt, no side airbags, 2WD vehicles

Images are for illustration purpose only. Actual product may vary.