RECARO BASE FRAME SEAT RAIL RIGHT SEAT FOR TOYOTA MARK X GRX130 133 2080.583.2

RECARO

BASE FRAME SEAT RAIL RIGHT SEAT

2080.583.2

TOYOTA MARK X GRX130 133

Model year: 2009-10-2019-12
Special notes: For vehicles with side airbags, the airbag warning light must be turned off. The seating position is almost the same as the OEM seat (when using ST-JJ center hole). The seat offset is about 10mm toward the door (the Recaro seat moves closer to the door). When a Recaro seat is installed on the passenger seat, the occupant detection sensor will not function and the seat belt warning light will not come on. The forward sliding amount is reduced by about 20mm compared to the OEM. The backward sliding amount is also reduced by about 20mm compared to the OEM.
Notes / Interference information: The seating position is higher for CS and CSE because a spacer is used. For RS/TS-# series, the steering wheel offset can be adjusted in 5mm increments from 5mm to a maximum of 15mm by using the RS/TS-G offset adapter set (product number 1700001J). (When installing, please consult your dealer regarding interference with the console side (shift, etc.)) Please adjust the RMS to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RMS side adapter before installing. Also, if there is interference with the interior, this can be alleviated by adjustment. Please adjust the RCS to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RCS side adapter before installing.
Position: New structure frame. English: Choose from 3 height levels (For some car models, the legs of the slide rail may need to be cut depending on the installation position, so please test fit before installation.)
Armrest: Cannot be installed
Compatible seats: LX / LX-# / LX-VS / LX-VF / LX-VL / Ergomed / Ergomed C / Ergomed D / Ergomed E / Ergomed LD / Ergomed MV (IS-84 base)
Classic LX Pepita / Classic LX Spektrum
LX-F (IS-05 base)
LS / LS-# / LT-#
CS / CR / CG / Conformed
CSE
Pro Racer RMS For the RMS, please adjust to the optimal position (front/rear height, left/right offset 0/5/10mm) using the separately sold RMS side adapter . Also, if there is any interference with the interior, it can be alleviated by adjustment. New Orthoped (with Recaro vent)
RCS Please adjust the RCS to the optimal position (front/rear height, left/right offset 0/5/10mm) using the separately sold RCS side adapter before installation. *Please choose from the following two types. ・RCS side adapter ・RCS stainless steel side adapter set SR-2 late model / SR-3 / SR-4 / SR-5 / SR-VF / SR-IMPACT / SR-IMPACT Pro
Rally Special / First generation SR / SR-2 early model
Late model A-8
Early model A-8
SP-A / SP-G / SP-G2 / SP-G3 / SP-GT / SP-GT2 You will need to purchase the side adapter set separately. SP-AN / SP-GN / SP-GN 2 SP-AN / SP-GN / SP-GN 2 require the separately sold SP-GN side adapter set (product number 1600110J). PRO RACER (RACER) SP-G/A side adapter set (product number 1700000J) must be purchased separately. AM19 TREND-J/JJ/JC
AM19 STYLE-J/JJ/JC
AM19 SPORT-J/JJ/JC
AM19 TREND-JS
AM19 STYLE-JS
AM19 SPORT-JS
AM19 TREND-D/DC
AM19 STYLE-D/DC
AM19 SPORT-D/DC/MAGNIFICA CL222HV
TS-G / RS-G / TS-W / RS-W For RS/TS-# series, please choose from two types of side adapter set or offset adapter set for RS/TS-G (sold separately). [Seating position priority] Side adapter set [Offset priority] Offset adapter set for RS/TS-G The handle offset can be adjusted to 5/10/15mm left and right. (The seating position is raised by +5mm.) SP-X
SR-6 /SR-11/SR-7
SR-S
SR-C/ SR-7F
Sportster
CrossSportster

(Note) This product cannot be installed on any seats other than those listed in the matching information below. Side airbag canceller included. 2WD vehicle.

Images are for illustration purpose only. Actual product may vary.