RECARO BASE FRAME SEAT RAIL RIGHT SEAT FOR NISSAN DUALIS J10 NJ10 2081.850.2

RECARO

BASE FRAME SEAT RAIL RIGHT SEAT

2081.850.2

NISSAN DUALIS J10 NJ10

Model year: 2007-05-2014-03
Special notes: The seating position is almost the same as the lowest position of the genuine seat (when using ST-JJ center hole). The forward sliding amount is reduced by about 20 mm compared to the genuine seat.
Cautions / Interference information: For LX (including Ergomed series), LS, and LT, the recliner dial on the center console side must be replaced with a thin recliner dial . For SR-3, 4, and 5, the recliner dial on the center console side must be replaced with a thin recliner dial . For CS, CSE, CT, and C-class seats, the seating position will be higher due to the use of a spacer. For RMS, please adjust to the optimal position (front-to-back height, left-to-right offset 0/5/10 mm) using the RMS side adapter sold separately. If there is interference with the interior, it can be alleviated by adjustment. Please adjust the RCS to the optimal position (front/rear height, left/right offset 0/5/10mm) using the separately sold RCS side adapter.
Position: New structure frame. Choose from 3 heights (For some car models, the legs of the slide rail may need to be cut depending on the installation position. Please perform a trial fit before installation.)
Armrest: Cannot be installed
Compatible seats: LX / LX-# / LX-VS / LX-VF / LX-VL / Ergomed / Ergomed C / Ergomed D / Ergomed E / Ergomed LD / Ergomed MV (IS-84 base) Replace with a thin recliner dial (sold separately) to avoid (reduce) interference with the vehicle Classic LX Pepita / Classic LX Spektrum Replace with a thin recliner dial (sold separately) to avoid (reduce) interference with the vehicle LX-F (IS-05 base)
LS / LS-# / LT-# Replace with a thin recliner dial (sold separately) to avoid (reduce) interference with the vehicle CS / CR / CG / Conformed
CSE
CT
C-Classic
Pro Racer RMS RMS should be installed after adjusting to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RMS side adapter . Also, if there is interference with the interior, it can be mitigated by adjustment. New Orthoped (with Recaro vent)
RCS RCS should be installed after adjusting to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RCS side adapter. *Please choose from the following two types.・Side adapter for RCS ・Stainless steel side adapter set for RCS Late model SR-2 / SR-3 / SR-4 / SR-5 / SR-VF / SR-IMPACT / SR-IMPACT Pro Replace with a thin recliner dial (sold separately) to avoid (reduce) interference with the vehicle Rally Special / First generation SR / Early model SR-2 Replace with a thin recliner dial (sold separately) to avoid (reduce) interference with the vehicle Late model A-8
Early model A-8
SP-A / SP-G / SP-G2 / SP-G3 / SP-GT / SP-GT2 You will need to purchase the side adapter set separately. SP-AN / SP-GN / SP-GN 2 SP-AN / SP-GN / SP-GN 2 require the separately sold SP-GN side adapter set (product number 1600110J). PRO RACER (RACER) SP-G/A side adapter set (product number 1700000J) must be purchased separately. AM19 TREND-J/JJ/JC
AM19 STYLE-J/JJ/JC
AM19 SPORT-J/JJ/JC
AM19 TREND-JS
AM19 STYLE-JS
AM19 SPORT-JS
AM19 TREND-D/DC
AM19 STYLE-D/DC
AM19 SPORT-D/DC/MAGNIFICA CL222HV
TS-G / RS-G / TS-W / RS-W Side adapter set (product number 1700000J) must be purchased separately. SP-X
SR-6 /SR-11/SR-7
SR-S
SR-C/ SR-7F
Sportster
CrossSportster

(Note) This product cannot be installed on any seats other than those listed in the matching information below.

Images are for illustration purpose only. Actual product may vary.