RECARO BASE FRAME SEAT RAIL RIGHT SEAT FOR MITSUBISHI AIRTREK CU2 4W 2083.271.2

RECARO

BASE FRAME SEAT RAIL RIGHT SEAT

2083.271.2

MITSUBISHI AIRTREK CU2 4W

Model year: 2001-01-2003-12
Notes: Not confirmed after minor change. The seating position is about 10mm higher than the original seat (when using ST-JJ center hole).
Notes / Interference information: Trend-J, JJ, JC, D, DC: Backrest side and door armrest interfere about 5-10mm. SR-1, 2: Backrest side and door armrest interfere about 5-10mm. SP-#, Racer requires SP-G offset adapter set . CS, CSE: Spacer is used, so the seating position is higher by the amount of the spacer. CT, C-Clutch: Center console side recliner cover must be removed, and the seating position is higher by the amount of the spacer. RMS: Please adjust to the optimal position (front-rear height, left-right offset 0/5/10mm) with the separately sold RMS side adapter before installation. If there is interference with the interior, it can be alleviated by adjustment. Please adjust the RCS to the optimal position (front/rear height, left/right offset 0/5/10mm) using the separately sold RCS side adapter.
Position: New structure frame. Choose from 3 different heights (For some car models, the legs of the slide rail may need to be cut depending on the installation position. Please test fit before installation.)
Armrest: Cannot be installed
Compatible seats: LX / LX-# / LX-VS / LX-VF / LX-VL / Ergomed / Ergomed C / Ergomed D / Ergomed E / Ergomed LD / Ergomed MV (IS-84 base)
Classic LX Pepita / Classic LX Spektrum
LX-F (IS-05 base)
LS / LS-# / LT-#
CS / CR / CG / Conformed
CSE
CT Remove the side cover (recliner cover) to avoid (reduce) interference with the vehicle C-Classic Remove the side cover (recliner cover) to avoid (reduce) interference with the vehicle Pro Racer RMS Please install the RMS by adjusting it to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RMS side adapter (product number 1700002J). If there is any interference with the interior, it can be alleviated by adjustment. New Orthoped (with Recaro vent)
RCS Please install the RCS by adjusting it to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RCS side adapter. *Please choose from the following two types.・Side adapter for RCS ・Stainless steel side adapter set for RCS SR-2 late model / SR-3 / SR-4 / SR-5 / SR-VF / SR-IMPACT / SR-IMPACT Pro
Rally Special / First generation SR / Early SR-2
Late model A-8
Early model A-8
SP-A / SP-G / SP-G2 / SP-G3 / SP-GT / SP-GT2 SP-# and Racer require the separately sold SP-G offset adapter set . SP-AN / SP-GN / SP-GN 2 SP-AN / SP-GN / SP-GN 2 require the separately sold SP-GN side adapter set . For PRO RACER(RACER) SP-G/A SP-# and Racer, you will need the separately sold SP-G Offset Adapter Set (Part number 1600094J). AM19 TREND-J/JJ/JC
AM19 STYLE-J/JJ/JC
AM19 SPORT-J/JJ/JC
AM19 TREND-JS
AM19 STYLE-JS
AM19 SPORT-JS
AM19 TREND-D/DC
AM19 STYLE-D/DC
AM19 SPORT-D/DC/MAGNIFICA CL222HV
TS-G / RS-G / TS-W / RS-W You will need to purchase the separately sold Side Adapter Set (Part number 1700000J). SP-X
SR-6 /SR-11/SR-7
SR-S
SR-C/ SR-7F
Sportster
CrossSportster

(Note) This product cannot be installed on any seats other than those listed in the matching information below.

Images are for illustration purpose only. Actual product may vary.