$269.00 SGD $28,600.00 SGD
| /
| Brand | RECARO |
| Series Name | BASE FRAME SEAT RAIL RIGHT SEAT |
| Product Number | 2086.001.2 |
| Compatible Car | SUBARU WRX VAB VAG |
| Product Description | Model year: 2014-08-2021-01 Special notes: The side airbag function built into the original seat will be lost. Vehicles equipped with side airbags require the airbag warning light to be turned off. The seating position is approximately 13 mm higher when using the upper position of the Recaro's three-stage adjustment compared to the lowest position of the original seat height adjustment function, approximately the same when using the center position, and approximately 13 mm lower when using the lower position. (When using ST-JJ). The handle offset of the Recaro seat is 5 mm closer to the door than the original seat. The slide position is 20 mm shorter forward than the original. When a Recaro seat is installed in the passenger seat, the occupant detection sensor will not function and the seat belt warning light will not be turned on. Notes / Interference information: For SP-# and Racer, the shoulder part may interfere with the B-pillar due to individual differences. For the RMS, adjust the RMS side adapter (front/rear height, left/right offset 0/5/10 mm) to the optimal position before installation. Also, if there is interference with the interior, it can be alleviated by adjustment. Please install the RCS after adjusting it to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RCS side adapter. For the old LX (including Ergomed series), since there is interference with the console, it is necessary to remove the recliner dial on the center console side and replace it with a rubber cap (product number 1600091J). Please remove the round recliner dial such as the LS. Please install the RCS after adjusting it to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RCS side adapter. Position: New structure frame. 3 height settings available (For some models, the legs of the slide rail need to be cut depending on the installation position. Please perform a trial fit before installation.) Armrest: Not compatible Compatible seats: LX / LX-# / LX-VS / LX-VF / LX-VL / Ergomed / Ergomed C / Ergomed D / Ergomed E / Ergomed LD / Ergomed MV (IS-84 base) Classic LX Pepita / Classic LX Spektrum LX-F (IS-05 base) LS / LS-# / LT-# Pro Racer RMS RMS is installed after adjusting to the optimal position (front-rear height, left-right offset 0/5/10mm) with the separately sold RMS side adapter RCS Please adjust the RCS to the optimal position (front/rear height, left/right offset 0/5/10mm) using the separately sold RCS side adapter before installation. *Please choose from the following two types. ・RCS side adapter AM19 STYLE-J/JJ/JC AM19 SPORT-J/JJ/JC AM19 TREND-JS AM19 STYLE-JS AM19 SPORT-JS AM19 TREND-D/DC AM19 STYLE-D/DC AM19 SPORT-D/DC/MAGNIFICA CL222HV TS-G / RS-G / TS-W / RS-W Side adapter set (product number 1700000J) must be purchased separately. SP-X SR-6 /SR-11/SR-7 SR-S SR-C/ SR-7F Sportster CrossSportster |
| Remarks | (Note) This product cannot be installed on any seats other than those listed in the matching information below. Side airbag canceller included. *All seats listed can be installed only on vehicles with electric parking brakes. For vehicles with manual side brakes, the brake lever and seat cushion will interfere with each other, so when installing an SR-series seat other than the SR-7F, install it at the lowest position of the three-stage adjustment. It cannot be installed in any other position because the manual side brake lever and seat cushion will interfere with each other. The lowest position of the frame with three-stage adjustment function is about 13 mm higher than the lowest position without using the adapter frame of the sports frame (part number 2086.003.1/2). |
| Notes | Images are for illustration purpose only. Actual product may vary. |
